Wavlink AC600 setup

A wireless extender can be used with the Wavlink AC600 setup to increase the coverage area of your current wireless network. It can operate on both the 2.4 GHz and 5 GHz bands because it is a dual-band extender. As a result, it can perform better than a single-band extender and offer faster speeds.

Here are the steps for Wavlink AC600 setup using WPS setup:

• You can activate the extender by plugging it into an electrical outlet.
• Wait until the power light is entirely green before proceeding.
• Find the WPS button on the extender’s back. A small, recessed button is typically where the “WPS” label is found.
• Press and hold the WPS button on your extender for two to three seconds.
• Hold the WPS button on the extender for two to three seconds within the next two minutes.
•  The moment the extender is connected to your extender, the power light will turn completely blue.

Manual Setup for Wavlink AC600 

Here are the steps on for Wavlink AC600 setup via Manual setup

• By inserting the extender into an electrical outlet, it will turn on.
• Hold off until the power light turns completely green.
• In the address bar of a web browser that is open, type 192.168.10.1.
• Typically, “admin” is used as both the username and password for default logins.
• Select “Extender” from the tabs Select “Repeater” as your mode.
• The Wi-Fi network password and SSID for your extender must be entered.
• Select “Connect” from the menu.
• The extender will join the Wi-Fi network created by your extender, and the power light will turn completely green.

Remember the following additional considerations for Wavlink AC600 setup:

• Ensure that your extender is within range. The signal strength indicator on the extender can be used to verify this.
• If the signal strength is poor, try moving the extender to a different location.
• Contact Wavlink customer service for support if you’re still having issues.

Wavlink AC600 Setup Features

Dual-band wireless connectivity is provided by the Wavlink AC600 setup, but difficulties occasionally occur. Use these troubleshooting suggestions to make sure your installation goes smoothly. 

The Wavlink AC600 has the following features, among others:

• Dual-band wireless: Compared to a single-band extender, the Wavlink AC600 can operate on both the 2.4GHz and 5GHz bands, enabling it to provide faster speeds and better performance.
• With a maximum speed of 600 Mbps, Wavlink AC600 is adequate for the majority of home and office use cases.
• The Wavlink AC600 is a good option for use in gardens, patios, and other outdoor areas due to its weatherproof construction, which enables it to withstand challenging outdoor conditions.
• The Wavlink AC600 can be installed quickly in remote locations without the need to run a separate power cable because it has the ability to be powered over Ethernet (PoE).
• All things considered, the Wavlink AC600 is a powerful and adaptable wireless extender that performs admirably in both homes and businesses.
• Fast speeds, a weatherproof design, and a variety of operation modes make it a fantastic choice for a wide range of applications.

How do I update the firmware?

Here are some quick and simple instructions for updating the firmware on your Wavlink AC600 setup:

• A Wavlink AC600 should be connected to the internet.
• Go to the management page for the extender. A common URL is ap.setup.
• Enter the login information “admin” for both the username and password to access the management page.
• The “Firmware Update” tab needs to be selected on the tabs.
• The “Check for Updates” button must be clicked.
• If a new firmware update is accessible, select “Download” from the menu.
• Once the firmware update has been downloaded, choose “Install” from the menu.
• The firmware update will be installed.
• The extender will be restarted.

How to perform factory reset on Wavlink AC600 extender ? 

The steps on how to perform a soft factory reset on the Wavlink AC600 extender  are as follows:

A quick way to restart the extender and solve any momentary issues is to perform a soft reset. These actions should be taken to perform a soft reset:

• On the extender’s back, look for the reset button. It is usually a tiny, recessed button with a “Reset” or “WPS” label.
• Using a paperclip or other pointed object, press and hold the reset button for five seconds.
• Switch off the button.
• The extender will be restarted.

The steps on how to perform a hard factory reset on the Wavlink AC600 extender  are as follows:

Performing a Hard Reset on the Wavlink AC600

A hard reset will erase all the settings on the extender and restore it to its factory defaults.

• On the extender’s back, look for the reset button. It is a tiny, recessed button with the letters “Reset” or “WPS” typically stamped on it.
• Press and hold the reset button for 8 seconds using a paperclip or another pointed object.
• Turn the button off.
• The LED indicators will flash and the extender will restart.
• The extender has been reset to factory defaults when the LED indicators are solid.

Once the extender has been reset, you will need to configure it again. You can do this by following the instructions in the extender’s manual or by visiting the Wavlink website.

When you reset your Wavlink AC600 extender, bear in mind the following additional considerations:

• Before you start, make sure the extender is connected to a power source.
• When the extender is being reset, avoid unplugging it.
• If the extender has any customised settings, you will need to change them after the reset.

Troubleshooting tips for the Wavlink AC600 setup

If issues continue, try restarting your system and thinking about contacting Wavlink’s customer support for specialised assistance. With these steps, you should be able to overcome typical setup difficulties and prepare your Wavlink AC600 installation for success.

• Verify the power light is on and that the extender is plugged into an outlet.
• Verify that the extender is within the extender’s range of coverage. You can check this by looking at the signal strength indicator on the extender.
• Try moving the extender to alter the situation. The signal strength can occasionally be significantly affected by a slight change in location.
• Try turning your extender back on. This occasionally resolves any immediate problems.
• If you’re still having problems, contact Wavlink customer service for assistance.
• Press the WPS button to pair the extender with your extender.
• The extender can be set up most easily using this technique.
• Entering the SSID of your Wi-Fi network will allow you to connect the extender to your extender if you are not using WPS.

You can get help from Wavlink customer service if you’re still having issues.